Enhanced TDS
Identification & Functionality
- Blend
- No
- CASE Ingredients Functions
- Chemical Family
- Chemical Name
- Industrial Additives Functions
- Product Code
- MITM16806
- Single Ingredient
- Yes
- Technologies
- Product Families
Features & Benefits
- CASE Ingredients Features
- Industrial Additives Features
- Labeling Claims
Applications & Uses
- Adhesive & Sealant End Applications
- Compatible Substrates & Surfaces
- Industrial Additives End Use
- Markets
- Applications
- Product Applications
- Bermocoll® E 511 X is used in cement-based tile fix and joint mortars for improvement of workability, consistency, water retention and adhesion. Normal dosage in mortars is 0.2 - 0.7 % calculated on the dry mortar weight. Bermocoll® E 511 X is also used in gypsum-based crack fillers.
- For this application, a suitable concentration is 0.6 - 0.8 %. Bermocoll® E 511 X is also used in gypsum-based projection plasters and glues. For this application, a suitable concentration is 0.2 - 0.6 %. Bermocoll® E 511 X is intended for dry mixing with other powder materials and should not be used for direct dissolving in water.
Properties
- Physical Form
- Soluble In
- Note
Bermocoll® E 511 X is a high viscosity grade of ethyl hydroxyethyl cellulose.
Safety & Health
- Safety and Handling
At high temperatures and in contact with an open flame, Bermocoll® E 511 X will burn slowly with the characteristics of cellulose.
Principal Information
- Group Principal Number
- S003175
- Principal
Storage & Handling
- Storage Conditions
- In unopened bags, Bermocoll® E 511 X can be stored for several years. In opened bags, the moisture content of Bermocoll® E 511 X will be influenced by the air humidity.
- At the temperatures above 250 °C (480 °F), charring of Bermocoll® E 511 X will occur.
Other
- Appearance
- Whitish powder
- Appearance (SDS)
- Powder
- Color (SDS)
- Off-white
- Dust Explosion Class (SDS)
- St1
- Flammability (SDS)
- Combustible solids
- Odor (SDS)
- Odorless
- Oxidizing Properties (SDS)
- Not oxidizing
- Protect from Freezing
- No
- Temperature Control
- No
- USA/DOT UN Number
- Not Applicable
- Application Information
Value Units Test Method / Conditions Dosage (Use Level) 0.6-0.8 % % in gypsum-based crack fillers Dosage (Use Level) 0.2-0.6 % % in gypsum-based projection plasters & glues Dosage (Use Level) 0.2-0.7 % % in mortars - Chemical Properties
Value Units Test Method / Conditions pH 7.0 - 1% Solution - Material Composition
Value Units Test Method / Conditions Salt Content max. 5.0 % % - Physical Properties
Value Units Test Method / Conditions Sieve Fractionation (Through) 98.0 % % max. 50 mesh, 300 µm Viscosity 6500.0-8000.0 mPa.s mPa.s Brookfield LV Viscometer at 20°C, 1% solution - SDS Physical and Chemical Properties
Value Units Test Method / Conditions Autoignition Temperature (SDS) min. 420.0 °C °C DIN EN 50281-2-1 Autoignition Temperature (SDS) min. 450.0 °C °C DIN EN 50281-2-1 auto-ignition of a dust cloud Autoignition Temperature (SDS) 120.0 °C °C EN 15188 at 5mm dust layer Burning Number (SDS) 5.0 - Decomposition Temperature (SDS) min. 100.0 °C °C Deflagration Index (SDS) max. 200.0 bar.m/s bar.m/s Kst Lower Explosion Limit (SDS) 30.0 g/m³ g/m³ Minimum Ignition Energy (SDS) min. 10.0 mJ mJ Viscosity (SDS) 6500.0-8000.0 mPa.s mPa.s at 20°C, pH 7 at 1% solution. pH (SDS) 5.5-8.0 - 0.5% concentration, aqueous solution