Enhanced TDS
Identification & Functionality
- Chemical Family
- Industrial Additives Functions
- Product Code
- MITM10512
- Technologies
- Product Families
Features & Benefits
- Industrial Additives Features
- Labeling Claims
Applications & Uses
- Compatible Substrates & Surfaces
- Industrial Additives End Use
- Markets
- Applications
- Product Applications
- Is suited for the water-repellent impregnation of porous mineral substrates
- Is very efficient on mineral renders, sand-lime brickwork, hard-baked brickwork, roofing tiles
- Shows very good penetration on absorbent mineral materials
- Gives water vapor permeable, colorless protection
- Reduces significantly the uptake of water
- Can be diluted with water
- We recommend using a minimum concentration of 10% of the active ingredient in water. This corresponds to a dilution with water (preferable demineralized water) of 1:4. Protectosil® WS 602 is not recommended to be applied undiluted. Minimum dilution rate should be 1:1.
- The concentration to be used and the exact amount to be applied are depending on the absorbance of the substrate.
- The substrates to be treated should be dry and clean. Acceptable surface cleaning methods include sandblasting and water blasting.
- During application outside temperatures and surface temperatures should be between 5 °C and 40 ° C. Protectosil® WS 602 should not be applied during strong wind or rain.
- Protectosil® WS 602 should be applied by wet-on-wet flow coating to the saturation point. The solution should be applied in 2 - 3 coats without drying between the coats. On vertical surfaces the solution should run down in the form of a clearly visible descending wet curtain. This is achieved by allowing the solution to flow against the surface of the building material without pressure. Most liquid delivery devices e.g. airless pumping equipment are suitable. The material should not be atomized or applied with a brush.
- The water repellent effect of Protectosil® WS 602 can develop within minutes or require up to several days depending on the substrate and weather conditions. Therefore, the impregnation should be applied continuously and without a break to avoid overlapping.
- Non-absorbent substrates such as window frames, window sills, plastic fittings, window glass, etc., should be covered before application. Surfaces which accidentally come into contact with Protectosil® WS 602 can be cleaned with alcohol (spirit) or aqueous soap solution. Cleaning should be carried out as quickly as possible (within a few hours), otherwise formation of a silicone resin film can make cleaning more difficult. Silicone resin films are best removed using ethanol (or spirit). Plant life should be protected from overspray.
- Protectosil® WS 602 reacts with the interfaces in pores and capillaries of the mineral surface and forms invisible, waterrepellent interfacial compounds. To determine the exact amount to be applied and to check whether previous or following treatments are compatible with the Protectosil® WS 602 treatment it is recommended to do a small test patch first.
Properties
- Physical Form
Regulatory & Compliance
Packaging & Availability
- Packaging Type
- Packaging Information
- Protectosil® WS 602 is supplied in 25 l PE-containers, 200 l steel drums with PE-inliner and 1.000 l containers.
Storage & Handling
- Storage Conditions
- Protectosil® WS 602 is not frost resistant and should not be stored at temperatures below 3 °C. Only demineralized water should be used for dilutions. Protectosil® WS 602 should be stored at temperatures between 3 °C and 40 °C. Protectosil® WS 602 has a shelf life of 12 months if properly stored in originally sealed containers.
Other
- Active Content
- 50.0 %
- Appearance
- White liquid
- Boiling Point (SDS)
- 100.0 °C
- Color (SDS)
- White
- Decomposition Temperature (SDS)
- min. 100.0 °C
- Density
- 1.017 g/cm³
- Density (SDS)
- 1.017 g/cm³
- Dosage (Use Level)
- min. 10.0 %
- Flash Point
- min. 90.0 °C
- Flash Point (SDS)
- min. 94.0 °C
- Item Number
- Melting Point (SDS)
- 30.0 °F
- Miscible in (SDS)
- Water
- Odor (SDS)
- Almost odorless
- Principal
- Shelf Life
- 12.0 mo
- Vapor Pressure (SDS)
- 23.0 hPa
- Viscosity
- 20.0 mPa.s
- Viscosity (SDS)
- 19.0 mPa.s
- pH
- 6.5-8.5
- pH (SDS)
- 6.5-8.5
- Chemical Properties
Value Units Test Method / Conditions pH 6.5-8.5 - at 20°C - Shelf Life & Stability
Value Units Test Method / Conditions Shelf Life 12.0 mo mo - Physical Properties
Value Units Test Method / Conditions Density 1.017 g/cm³ g/cm³ DIN 51757 At 20°C Flash Point min. 90.0 °C °C EN 22719 Viscosity 20.0 mPa.s mPa.s DIN 53015 At 20°C - Material Composition
Value Units Test Method / Conditions Active Content 50.0 % % - Application Information
Value Units Test Method / Conditions Dosage (Use Level) min. 10.0 % % active ingredient in water - SDS Physical and Chemical Properties
Value Units Test Method / Conditions Boiling Point (SDS) 100.0 °C °C Decomposition Temperature (SDS) min. 100.0 °C °C Density (SDS) 1.017 g/cm³ g/cm³ DIN 51757 at 20°C Flash Point (SDS) min. 94.0 °C °C Melting Point (SDS) 30.0 °F °F Vapor Pressure (SDS) 23.0 hPa hPa At 20°C Viscosity (SDS) 19.0 mPa.s mPa.s DIN 53015 at 20°C pH (SDS) 6.5-8.5 - at 20°C