Products

AEROSIL® 150 is a hydrophilic fumed silica with a specific surface area of 150 m²/g

AEROSIL® 200 VS is a densified hydrophilic fumed silica with a specific surface area of 200 m²/g.

AEROSIL® R 106 Coating is a hydrophobic fumed silica surface treated with D4 (octamethylcyclotetrasiloxane).

AEROSIL® R 711 is a fumed silica aftertreated with a methacrylsilane.

AEROSIL® R 974 W is a hydrophobic fumed silica after treated with DDS (Dimethyldichlorosilane) based on a hydrophilic fumed silica with a specific surface area of 200m²/g. The product thickening efficiency of AEROSIL® R 974 W ex RHE is consistent with the Waterford-produced AEROSIL® R 974. This profile is different than the thickening profile of standard RHE quality.

AEROSIL® R 976 S is a hydrophobic fumed silica aftertreated with DDS (Dimethyldichlorosilane).

3M™ Boron Nitride Cooling Filler Agglomerates 250S is a versatile ceramic material offering thermal conductivity, temperature stability, chemical resistance, high reflectivity, lightweighting and electrical insulation. The structure of layered hexagonal plates provides outstanding lubricating properties and is non-abrasive to tooling.

3M™ Boron Nitride Cooling Filler Platelets 003 is a versatile ceramic material offering thermal conductivity, temperature stability, chemical resistance, high reflectivity, lightweighting and electrical insulation. The structure of layered hexagonal plates provides outstanding lubricating properties and is non-abrasive to tooling.

3M™ Boron Nitride Cooling Filler Platelets 006 is a versatile ceramic material offering thermal conductivity, temperature stability, chemical resistance, high reflectivity, lightweighting and electrical insulation. The structure of layered hexagonal plates provides outstanding lubricating properties and is non-abrasive to tooling.

AQUAPOL® PI-13000-31 Prepolymer is an aliphatic urethane, end-capped prepolymer con- taining un-reacted isophorone diisocyanate (IPDI). Aquapol PI-13000-31 prepolymer will gel up to five times its weight of water and can be used to form stable gels with water. In contrast, concentrations of Aquapol PI-13000-31 prepolymer above 50% will result in closed cell foam rather than a gel. Gels will lose water to the atmosphere and should be protected with an impermeable membrane. The speed of reaction can be increased or decreased by using warm or cold water respec- tively and by the concentration of the amine catalyst. Using cold water will reduce any tendency toward frothiness.

AQUAPOL® PT-17000-62 Prepolymer is a toluene diisocyanate-based urethane polymer uti- lized in the manufacturing of hydrophilic foams and coatings. Aquapol® PT-17000-62 pre- polymer has found use in a wide range of applications ranging from medical foams, visco- elastic earplugs, cosmetic sponge, and specialty coatings and foams. Due to the hydro- philic backbone, this polymer and resultant foams and coatings absorb and retain a large quantity of liquid (water and alcohol).

Baerostab® B-1657 is a liquid Potassium/Zinc Stabilizer and Kicker.

Baerostab® BZ 8785 - US is a Zn liquid stabilizer and kicker.

Baling® SEPS YH-4010 is a 37% combined styrene content and 100% diblock content. The product is powder and cosmetic white oil thickening, cosmetic water retention ointment. The product has stable physical and chemical properties, good viscosity-temperature performance, and is easy to pump into the fiber when it is applied to the optical fiber filling grease, and has a low oil separation rate.