Products

Exolit® AP 422 is a fine-particle ammonium polyphosphate (phase II) produced by a special method. The product is largely insoluble in water and completely insoluble in organic solvents. It is colorless, non-hygroscopic and non-flammable.

Exolit® AP 462 is a product based on ammonium polyphosphate. The crystal modification is phase II. It is manufactured from ammonium polyphosphate by micro-encapsulation with melamine resin according to Clariant’s own method. Exolit® AP 462 is a fine-particle white powder with very low solubility in water, even at elevated temperatures. It is completely insoluble in organic solvents. The product is non-hygroscopic and non-flammable.

CARPOL® GP-5171 is a glycerin-initiated polyether polyol. The resulting material has a nominal functionality of three and an average molecular weight of 5000 Da. This triol is polymerized with propylene oxide and then capped with 71% ethylene oxide. The outcome is a polyol with enhanced reactivity. Main applications include flexible foam, however, CARPOL® GP-5171 may also be included as a component in other urethane products and applications.

CARPOL® SPA-530 is a sucrose amine-initiated polyether polyol. The high functionality of the initiators yields a resultant polyol with a nominal functionality of 5.5 and a typical hydroxyl number of 530. This polyol’s functionality and short-chained nature make it optimal for use in rigid foam. In addition, CARPOL® SPA-530 contains amine and therefore is autocatalytic. This allows the formulator to use less catalyst while achieving the same reactivity seen in other neutral rigid polyols.

Exolit® AP 422 A is a fine-particle ammonium polyphosphate (phase II) with less than 0.1% melamine. The product is largely insoluble in water and completely insoluble in organic solvents. It is colorless, non-hygroscopic, non-flammable, and classified as SVHC-free under current regulations.

Exolit® AP 428 is a fine-particle ammonium polyphosphate produced by a special method. The product is largely insoluble in water and completely insoluble in organic solvents. It is colorless, non-hygroscopic and non-flammable. Exolit® AP 428 differs from most other commercial products in the following ways: - greatly reduced solubility in water lower viscosity in aqueous suspensions - lower viscosity in PU polyol suspensions.

Cotin® 228 W/Xylene is a liquid organotin carboxylate catalyst recommended for use in room temperature vulcanised (RTV) silicone systems and polyurethane foams and elastomers. Cotin® 228 W/Xylene should be considered a “moderate to rapid” catalyst, for relatively faster cure. It does not utilize acetic acid in its manufacture, and therefore, does not have the odor or corrosiveness normally associated with organotin acetates.

Bluesil™ FLD 47 V50 is straight chained polydimethylsiloxanic fluids.

CARPOL® PGP-400-50 is a propylene glycol-initiated polyether polyol. The resulting material has a nominal functionality of two and a molecular weight of 400 Da. The low functionality and viscosity of this polyol makes for a versatile product. It may be used in rigid foam systems to lower the viscosity of B-side materials while helping control crosslinking.

CARPOL® GP-5171-60 Polyol is a glycerin-initiated polyether polyol. The resulting material has a nominal functionality of three and an average molecular weight of 5000 Da. This triol is polymerized with propylene oxide and then capped with 71% ethylene oxide. The outcome is a polyol with enhanced reactivity. Main applications include flexible foam, however, CARPOL® GP-5171-60 Polyol may also be included as a component in other urethane products and applications.

3M™ Glass Bubbless H20/1000 is a engineered hollow glass microspheres that are alternatives to conventional fillers and additives such as silicas, calcium carbonate, talc, clay, etc., for many demanding applications. These low- density particles are used in a wide range of industries to reduce part weight, lower costs and enhance product properties.

Bluesil™ FLD 47 V100 is straight chained polydimethylsiloxanic fluids.

CARPOL® GP-1500 is a glycerin-initiated polyether polyol. The resulting material has a functionality of three and an average molecular weight of 1500 Da. This triol is polymerized solely with propylene oxide for controlled reactivity. Main applications include C.A.S.E., however, CARPOL® GP-1500 may also be included as a component in other urethane products and formulations.

TEDA-L33E is a chemical mixture and blend used as a catalyst in industrial additives.

Cotin® 227 is a dibutyltin diacetate, a liquid organotin catalyst recommended for the manufacture of silicone and polyurethane systems. It can be used in these primary reactions as well as secondary types such as allophanate and biuret formation.