Products

MAINCOTE™ HG-31 is a binder and resin classified under chemical mixtures and blends.

Stabaxol® P 100 PASTILLES is a carbodiimide-based anti-hydrolysis agent used in plastics and elastomers.

CRAYVALLAC® PA4 WDA 12 is a pre-activated amide wax supplied in a mixture of mineral spirit (D60) and alcohols. Under paste form for post addition to solvent-based low polarity coating systems, it provides a very simple and direct mean of introducing shear-thinning rheology with thixotropic viscosity recovery to coating formulations. It is a softer version than CRAYVALLAC® PA3 WDA 20 with enhanced ease of incorporation. It is also a very cost efficient alternative to organoclays. The shear-thinning characteristic provides a very high viscosity under the low shear rates and a low viscosity at the much higher application shear rates. The net result is excellent control of sedimentation combined with ease of application. Immediately following application, the coating’s viscosity undergoes a time dependent recovery as the network re-establishes itself. This time dependence is known as thixotropy and enables the final coating to attain very good levelling.

EBECRYL® LEO 10502 is a low viscosity polymeric tetrafunctional polyether acrylate that provides low extractables, low odor and low migration after UV or EB curing. EBECRYL® LEO 10502 is recommended for use in low odor and low migrating UV/EB curable overprint varnishes (OPV’s) and inks.

WANNATE® HT-100 is a solvent free aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI), colorless to slightly yellowish clear liquid.

EBECRYL® 81 is an amine modified polyether acrylate that exhibits very low viscosity and fast cure via exposure to ultraviolet light (UV). Films of EBECRYL 81 cured by UV or electron beam (EB) demonstrate high gloss and low residual odor. EBECRYL® 81 is especially suited to applications requiring low viscosity and fast UV cure, including overprint varnishes and flexographic inks.

Europrene® K SOL 1205 is a solution styrene butadiene partial block copolymer, polymerized using an alkyl lithium catalyst at the Yeosu production facility in Korea. A non staining, BHT and TNPP free antioxidant system is added during the production process.

HECTGEL RD is a synthetic layered silicate consisting of Li, Mg and Si. Its structure is constituted by two layers of Si-O tetrahedron with one layer of Mg-O octahedron. It can hydrate with water and swell to form clear and colorless colloidal dispersions. Highly thixotropic gels can be formed at concentrations of 2% or more and these gels demonstrate highly shear thinning behavior. HECTGEL RD is used where a shear sensitive waterborne gel structure is desired, having high viscosity under low shear and low viscosity when exposed to high shear. Upon removal of shear the gel viscosity is quickly recovered.

Focus Additive RP RZ8 is a very cost effective water-soluble corrosion inhibitor additive designed to impart temporary rust protection for ferrous and non-ferrous applications. It does not contribute to discoloration on the surface of non-ferrous metals. It imparts lubrication properties when used at higher concentrations. It is designed to have a relatively low pH and high acid content, which provides the ability to formulate fluid concentrates with a variety of alkaline sources. Focus Additive RP RZ8 is non-foaming and has excellent stability in hard water up to 1500 ppm hardness. Focus Additive RP RZ8 gives rust protection when water evaporates. The thin liquid film that remains provides rust protection to ferrous surfaces, even under high humidity conditions. This film can easily be removed by rinsing with water. It also burns off cleanly in high temperature processing operations. Focus Additive RP RZ8 is composed of a mixture of organic acid salts, is DEA free and can be waste treated by adjusting the pH below the methyl orange end point.

ACRYSOL™ DR-5500 is a new associative thickener that delivers the same performance as ACRYSOL RM-5, but without the use of APEO surfactants. ACRYSOL™ DR-5500 provides excellent gloss, film build, and flow in latex paints. Being both APEO-free and solvent-free, ACRYSOL™ DR-5500 is ideally suited to meet the latest regulatory requirements for waterborne paints and coatings. This product enhances high shear (ICI Cone and; Plate) viscosity, resulting in coatings with high film build characteristics, improving hiding and appearance. Additional benefits for manufacturers include minimal roller spatter and the full realization of gloss potential in latex paints. Since ACRYSOL™ DR-5500 uses hydrophobically-modified alkali-soluble chemistry, it offers a high degree of resistance to bacterial and enzymatic attack, ensuring long-term paint viscosity stability.

Solumer™ 851T is an ultra-low density ethylene-octene copolymer produced via NexleneTM technology. It has excellent flow characteristics and provides superior impact resistance with other polymers.

GRANOLITE® TEG is a triethylene glycol- esterified rosin resin with low viscosity and very low VOC content. Thanks to its low viscosity, it flows easily and is ideal for use as a tackifier and plasticizing agent in various adhesive formulations, particularly for construction.

3M™ Boron Nitride Cooling Filler Agglomerates 50M is a versatile ceramic material offering thermal conductivity, temperature stability, chemical resistance, high reflectivity, lightweighting and electrical insulation. The structure of layered hexagonal plates provides outstanding lubricating properties and is non-abrasive to tooling.