Products

Rilsan® BMNO P40 TLD is a polyamide 11 produced from a renewable source. Rilsan® BMNO P40 TLD is plasticized and designed for injection molding.

PEBAX® MH 1657 resin is a thermoplastic elastomer made of flexible polyether and rigid polyamide. Pebax® MH 1657 resin is an inherently dissipative polymer and can be dry blended or compounded with an isolative polymer to lower the surface resistivity of the final part. This hydrophilic grade when extruded into either a thin film or laminated on to a substrate also offers excellent permeability to moisture vapor while remaining waterproof.

Agimid® 241 N070 is a plasticized and impact modified PA12 extrusion grade.

Rilsan® BZM 23 G9 is a fiberglass reinforced polyamide 11 produced from a renewable source. Rilsan® BZM 23 G9 with improved friction properties is designed for injection molding.

PEBAX® MV 1074 SP 01 resin is a thermoplastic elastomer made of flexible polyether and rigid polyamide. Pebax® MV 1074 SP 01 resin is an inherently dissipative polymer and can be dry blended or compounded with an isolative polymer to lower the surface resistivity. This hydrophilic grade when extruded into either a thin film or laminated on to a substrate offers excellent permeability to moisture vapor while remaining waterproof. This SP grade has been developed to be heat and UV resistant.

ORGASOL® 2002 EXD NAT 1 is an ultrafine powder of polyamide 12 with a narrow particle size distribution and nearly round particle shape.

Rilsan® D40 Blanc are specialty PA powders obtained from renewable ressources. Rilsan® D40 Blanc show outstanding performances such as anti-corrosion, chemical, impact, abrasion, graffiti resistance.

Rilsan® INVENT SP is a polyamide 11 (PA 11) resin used in plastics and elastomers applications.

AP 1041X90 is a medium viscosity reactive, Mannich-based amine hardener for epoxy resins based lacquers and coatings.

CRAYVALLAC® PA4 WDA 12 is a pre-activated amide wax supplied in a mixture of mineral spirit (D60) and alcohols. Under paste form for post addition to solvent-based low polarity coating systems, it provides a very simple and direct mean of introducing shear-thinning rheology with thixotropic viscosity recovery to coating formulations. It is a softer version than CRAYVALLAC® PA3 WDA 20 with enhanced ease of incorporation. It is also a very cost efficient alternative to organoclays. The shear-thinning characteristic provides a very high viscosity under the low shear rates and a low viscosity at the much higher application shear rates. The net result is excellent control of sedimentation combined with ease of application. Immediately following application, the coating’s viscosity undergoes a time dependent recovery as the network re-establishes itself. This time dependence is known as thixotropy and enables the final coating to attain very good levelling.

Rilsan® BESN BLACK TL is a polyamide 11 produced from a renewable source. Rilsan® BESN BLACK TL is designed for extrusion.

CRAYVALLAC® SLX is a high performance micronised amide wax rheology modifier designed for the low temperature manufacture of moisture curing methoxysilane systems, where processing temperatures typically lie within the range 60 - 90°C. CRAYVALLAC® SLX particles are converted to an interacting network of crystalline fibres. It is this network that gives rise to the shear thinning rheology. This shear thinning characteristic provides for a low viscosity at the shear rates associated with application by extrusion, and a very high viscosity under the low shear rates experienced after application. The net result is ease of application followed by excellent sag and slump resistance.

Rilsan® ROTO 11 NATURAL is a binder and resin used in chemical manufacturing, functioning as a binder.

CRAYVALLAC® SLW is a high performance micronized amide wax rheology modifier designed for manufacture of one component Silyl-Terminated-Polymer based adhesives and sealants, especially for highly filled systems (demanding applications, High-Tack systems for instance).

Rilsamid® AESNO P401 TL is a natural polyamide. This grade is plasticized and designed for tube extrusion.