Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Code
- MITM09813
- RTU Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
Applications & Uses
- Compatible Polymers & Resins
- Compatible Substrates & Surfaces
- Application and Usage Information
- Direction of Use:
- Preliminary Statement:
- Prior to use it is necessary to read the Material Safety Data Sheet for information about precautionary measures and safety recommendations. Also, for chemical products exempt from compulsory labeling, the relevant precautions should always be observed. Please also refer to the local safety instructions and contact Henkel for analytical support.
- Pretreatment:
- The performance attained with BONDERITE® S-OT 310Bdepends on the substrate preparation, application and curing.
- Substrates should be clean and dry before application. A solvent wipe and air dry is usually sufficient. For critical applications requiring maximum adhesion, mechanical or chemical pretreatment such as grit or vapour blasting, phosphating, anodising or etching is recommended. Specific recommendations will be provided upon request.
- Mixing:
- BONDERITE® S-OT 310Bis marketed as a two-package system in combination with BONDERITE L-GP T A COMP ACHESON which should be mixed just before use.
- The white BONDERITE L-GP T A COMP ACHESON, first properly homogenised by rolling, should be added very slowly to the blue BONDERITE® S-OT 310Bwith continuous, slow agitation, just enough to get a proper vortex, by a propeller-type mixer or equivalent.
- Be sure that the BONDERITE L-GP T A COMP ACHESON does not build up as a layer on the bottom of the container, but avoid excessive agitation which will cause curdling. The resulting mixture should be a smooth dispersion. It is ready for use, though it should be agitated gently from time to time during actual application.
- Only enough for immediate use should be mixed. If smaller amounts of mix are needed, 22 parts by weight of the BONDERITE L-GP T A COMP ACHESON should be used for every 100 parts by weight of the BONDERITE S-OT 310B ACHESON. Do not add further diluents to the mix.
- Preliminary Statement:
- Application:
- Use an external-atomizing spray gun with 2 to 3 bar air pressure and adjust the gun to give a well-atomized spray. For optimum performance, the final coating thickness should be 10 to 25 μm.
- For thicker coatings use multiple passes pausing a few minutes between passes to permit air drying. For rubber substrates a coating thickness of 5 to 10 μm is recommended.
- When properly applied, the coating will be even and free of runs, blisters or "fish eyes".
- Electrostatic spray equipment suitable for products with very low internal resistance may be used to apply BONDERITE S-OT 310B ACHESON.
- Curing:
- For optimum results, BONDERITE® S-OT 310Bshould be cured on either one of the three following curing cycles:
- 60 minutes/ 160°C (substrate temperature)
- 30 minutes/ 180°C (substrate temperature)
- 10 minutes/ 200°C (substrate temperature)
- For optimum results, BONDERITE® S-OT 310Bshould be cured on either one of the three following curing cycles:
- Cleaning up
- Spray guns, tanks, mixing hardware and spills of BONDERITE® S-OT 310Bcan easily be cleaned with MEK. Cured coatings can be removed by sand blasting or soaking in hot caustic solutions.
- Direction of Use:
Properties
- Physical Form
Regulatory & Compliance
Packaging & Availability
- Packaging Type
Principal Information
- Group Principal Number
- S000218
- Principal
Storage & Handling
- Storage and Shelf Life Information
- Recommended Storage Temperature, 5 to 30°C, Shelf-life 18 months (in unopened original packaging)
Other
- Color
- Green
- Color (SDS)
- Blue
- IATA/ICAO Proper Shipping Name
- Resin solution
- IATA/ICAO UN Number
- UN 1866
- IMO/IMDG Proper Shipping Name
- Resin solution
- IMO/IMDG UN Number
- UN 1866
- Item Number
- Odor (SDS)
- Solvent
- USA/DOT Proper Shipping Name
- Resin solution
- USA/DOT UN Number
- UN 1866
- Shelf Life & Stability
Value Units Test Method / Conditions Shelf Life1 18.0 mo mo - Mechanical Properties
Value Units Test Method / Conditions Coefficient of Friction 0.06 - as static and kinetic - Physical Properties
Value Units Test Method / Conditions Coverage 7.7 m²/kg m²/kg of wet product Density 910.0 kg/m³ kg/m³ Flash Point 8.0 °C °C - Material Composition
Value Units Test Method / Conditions Solid Content 10.5 % % of wet product - Application Information
Value Units Test Method / Conditions Application Temperature 160.0 °C °C Application Temperature 150.0 °C °C continuous - SDS Physical and Chemical Properties
Value Units Test Method / Conditions Autoignition Temperature (SDS) min. 272.0 °C °C Boiling Point (SDS) min. 35.0 °C °C Flash Point (SDS) 7.8 °C °C ASTM D93 Lower Explosive Limit (SDS) 1.1 % % Melting Point (SDS) max. 0.0 °C °C Relative Vapor Density (SDS) min. 1.0 - Air = 1 Specific Gravity (SDS) 0.9-0.92 - Upper Explosion Limit (SDS) 36.5 % % Vapor Pressure (SDS) 20.0 mm Hg mm Hg at 20°C Viscosity (SDS) 25.0 cPs cPs Volatile Organic Content (VOC) (SDS) 772.0 g/L g/L