Products

AP 1465 is an excellent light color and a low viscosity phenalkamine curing agent suitable for epoxy coating primarily for top coat application. The product has rapid cure and film properties at lower temperature and excellent adhesion on concrete, primers, and mid coats. This product is designed primarily for floor topcoat and self leveling applications due to its good hardness, mechanical properties, and gloss and color retention.

Exolit® AP 428 is a fine-particle ammonium polyphosphate produced by a special method. The product is largely insoluble in water and completely insoluble in organic solvents. It is colorless, non-hygroscopic and non-flammable. Exolit® AP 428 differs from most other commercial products in the following ways, greatly reduced solubility in water lower viscosity in aqueous suspensions, lower viscosity in PU polyol suspensions.

AP 5904 is a low viscosity, modified Cycloaliphatic amine adduct hardener for epoxy resin based lacquers and coatings.

AP 5977 is a low viscosity modified polyamide curing agent for epoxy resin based lacquers and coatings.

AP 4237 is a low viscosity, Long Pot-life, modified aliphatic amine hardener for epoxy resins based coatings. Suitable for high solids or solvent free coatings.

CRAYVALLAC® 60X is used in epoxies (EP) and vinyls. It is applied in anti-fouling coatings, chlorinated rubber coatings, primers, and solventborne coatings. The product provides anticaking, recoatability, and sag resistance.

Exolit® AP 435 is a fine particle ammonium polyphosphate (phase II) optimized for low viscosity in aqueous suspension and intumescent coatings. The product is largely insoluble in water and completely insoluble in organic solvents. It is colorless, non-hygroscopic and non-flammable.

CRAYVALLAC® MT is used in solventborne coatings, as well as solventless and high solids coatings. It features anti-settling, high thixotropy, recoatability, and sag resistance. The product functions as a rheology modifier in CASE ingredients.

CRAYVALLAC® ANTISETTLE CVP is used in caulks, solventborne coatings, and greases. It features anti-settling, good leveling, high shear thinning, high thixotropy, recoatability, and sag resistance. The product functions as a rheology modifier in CASE ingredients.

Exolit® AP 750 is a non-halogenated flame retardant based on ammonium polyphosphate as main component, which develops its effectiveness through phosphorus/nitrogen synergism. In contrast to similar competitive material, it shows high processing stability. Exolit® AP 750 differs in its mode of action from non phosphorus-based flame retardants (e. g. brominated, chlorinated or mineral FRs like ATH) by achieving its effect through intumescence. Material containing Exolit® AP 750 will foam on exposure to flame. The carbon-rich foam layer so formed will protect the polymer and in many cases the substrate below through its heat insulating effect, reduces further oxygen access and prevents dripping in case of a thermoplastic based formulation. Beyond the primary effects on fire behavior such as reduction of flame propagation rate, rate of heat release, dripping behavior, residual lengths of test specimens after flame tests etc., positive secondary fire effects such as low smoke density, no release of corrosive off-gasses, lower formation of toxic smoke gasses are of great interest.

Exolit® AP 462 is a product based on ammonium polyphosphate. The crystal modification is phase II. It is manufactured from ammonium polyphosphate by micro encapsulation with melamine resin according to Clariant’s own method. Exolit® AP 462 is a fine particle white powder with very low solubility in water, even at elevated temperatures. It is completely insoluble in organic solvents. The product is non-hygroscopic and non-flammable.

CRAYVALLAC® ULTRA is a pure polyamide especially recommended in 2K epoxy primers for its robustness. CRAYVALLAC® ULTRA is a micronised amide wax rheology modifier offering very good recoatability for ambient curing solvent-based epoxy coatings. CRAYVALLAC® ULTRA has been designed to overcome those difficulties which exist with older type organo-wax rheology modifiers e.g. seeding, false-body and migration of readily dissolved species to the surface. Consequently, when used in strong solvent systems, coatings formulated using CRAYVALLAC® ULTRA offer an enhanced performance and very good recoatability.

AP 1063 is very a low viscosity, 100 % solids reactive Phenalkamine adduct hardener with improved blush resistance. It is suitable for low temperature curing of epoxy coating.

AP 5637 is a curing agent used in CASE (Coatings, Adhesives, Sealants, and Elastomers) applications. It facilitates the curing process in various resin systems, enhancing their mechanical properties for improved performance in industrial applications.

Exolit® AP 422 is a fine-particle ammonium polyphosphate (phase II) produced by a special method. The product is largely insoluble in water and completely insoluble in organic solvents. It is colorless, non-hygroscopic and non-flammable.