Products

AP 8016L is a unique light color epoxy reactive diluents for epoxy- amine systems derived from Card phenol. With mono epoxy group per mole, it reduces excessive cross linking of the system and with side chain, imparts flexibility to paint films.

AP 1563 is a low viscosity, reactive, Phenalkamine epoxy hardener solution for epoxy resins based lacquers and coatings.

Exolit® AP 750 is a non-halogenated flame retardant based on ammonium polyphosphate as main component, which develops its effectiveness through phosphorus/nitrogen synergism. In contrast to similar competitive material, it shows high processing stability. Exolit® AP 750 differs in its mode of action from non phosphorus-based flame retardants (e. g. brominated, chlorinated or mineral FRs like ATH) by achieving its effect through intumescence. Material containing Exolit® AP 750 will foam on exposure to flame. The carbon-rich foam layer so formed will protect the polymer and in many cases the substrate below through its heat insulating effect, reduces further oxygen access and prevents dripping in case of a thermoplastic based formulation. Beyond the primary effects on fire behavior such as reduction of flame propagation rate, rate of heat release, dripping behavior, residual lengths of test specimens after flame tests etc., positive secondary fire effects such as low smoke density, no release of corrosive off-gasses, lower formation of toxic smoke gasses are of great interest.

AP 4406 is modified aliphatic amine hardener used with liquid epoxy resin based systems at ambient as well as low temperature.

AP 1442 is a medium viscosity reactive, phenalkamine hardener for epoxy resins based lacquers and coatings.

ZHENGDA® ZD-123 is characterized by repeating oxypropylene units in the backbone. ZHENGDA® ZD-123 Amine-terminated Polyether is a difunctional, primary amine with an average molecular weight of about 230. The primary amine groups are located on secondary carbon atoms at the end of the aliphatic polyether chain.

AP 5635 is a low viscosity, modified Cycloaliphatic amine adduct hardener for epoxy resin based lacquers and coatings.

PURMOL™ 3ST is a potassium (K) type A zeolite with a pore size of approximately 3 Angstroms (0.32 nm). Purmol 3ST is recommended for use with high quality coatings. In general, we recommend the addition of 2.5% - 5% Purmol powder to the polyol component. This must be stirred thoroughly for a minimum of two hours to allow the Purmol to adsorb all the water before addition of the isocyanate.

D.E.H.® 20 Epoxy Curing Agent is an economical, liquid diethylenetriamine (DETA) aliphatic polyamine hardener that provides a short pot-life and cures in minutes with standard unmodified liquid epoxy resins. D.E.H.® 20 Epoxy Curing Agent is used for civil engineering applications, maintenance paints, and in the manufacture of epoxy-amine adducts. It is also used in adhesives, epoxy composite applications and as an accelerator for polyamide curing agents. In electrical applications, D.E.H.® 20 Epoxy Curing Agent is used for casting, potting and encapsulation.

Hostavin® 3055 liq is a low-molecular radical scavenger of the type hindered amine light stabilizer (HALS) for solventless and solventborne paints. On principle, it is also suitable in waterbome coatings. Hostavin® 3055 liq is characterized by its excellent solubility, broad compatibility, low volatility and good stabilization efficiency. It can either be added to the ready-to-use paint or incorporated during the paint production. However, as all UV stabilizers, it ought not to be added to the mill-base. Depending on the requested stabilization effect, the addition rate should be in the range of 1.0 to 3.0 %. All concentrations relate to active UV stabilizer on solid resin. Pre-trials, covering various concentrations, are highly recommended. As a non-substituted HALS, Hostavin 3055 liquid is slightly basic and because of this can have an influence on the crosslinking of binders. In such a case, the altemative use of Hostavin 3058 liquid is recommended. Since HALS is highly recommended for all outdoor durable coatings, the need for an additional UV absorber strictly depends on the UV transmittance of the final coating. Inorganically pigmented coatings with good hiding power do usually not require an additional UV absorber, clear coats certainly do.

AP 5601 is low Viscosity, reactive polyamido amine hardener for epoxy resins based coatings.

WANAMINE™ 8100 is a curing agent and surfactant used in adhesives, sealants, plastics, and elastomers.

Vorite® 115 has been polymerized by a unique process, which imparts excellent thermal and viscosity stability. They function as polymeric plasticizers for elastomers in adhesive and sealant applications.

AP 5604 is a low viscosity, Long Pot-life, modified aliphatic amine hardener for epoxy resins based coatings. Suitable for high solids or solvent free coatings.

AP1405 is Low viscosity, reactive, mannish-based amine hardener for epoxy resins based lacquers and coatings.