Enhanced TDS
Identification & Functionality
- Chemical Family
- Country of Origin
- Product Code
- MITM04879
- RTU Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Key Features and Benefits
- Product Features:
- Chionso
- Satiny finish
- Low coefficient of friction
- Extremely durable and wear-resistant coating
- Good release properties with a low coefficient of friction
- Wide range of solvent and chemical resistance
- Product Benefits
- Attractive component appearance to secure customer satisfaction
- Ability to meet lubrication requirements for the component
- Application for a variety of demanding lubrication performance requirements
- Ability to meet lubrication and assembly requirements for the component and application
- Ability to perform optimally in a variety of harsh environments Chionso Satiny finish
- Low coefficient of friction
- Extremely durable and wear-resistant coating
- Good release properties with a low coefficient of friction Wide range of solvent and chemical resistance
- Product Features:
Applications & Uses
- Application Area
- Compatible Polymers & Resins
- Markets
- Applications
- Application and Usage Information
- Product Application:
- Business machine partsValve plugs
- Drawer guides
- Snow shovels
- Trash containers
- Filter systemsCarburetor shaftsWindow guides
- Rails
- Wheels
- Levers
- Washers
- Springs
- Valves
- Hedge shears
- Saw blades
- Latches
- Slides and chutes
- Marine equipment
- Spray gun parts
- Lock assemblies
- Industrial tools
- Printing equipment
- Aerospace parts
- Tank linings
- Slides and chutes
- Closed automotive assemblies
- Usage Information:
- Surface Preparation
- Substrates must be dry and free of contaminants (dirt, grease, powder, and other residues) before application of BONDERITE S-FN 333 ACHESON (known as EMRALON 333). Excellent results can be obtained without pre-treatment. However, for maximum wear characteristics the following pre-treatment’s are recommended: heat stable phosphate coating* or grit blasting for steel; grit blasting or heat stable conversion coating for aluminum.
- Mixing
- BONDERITE S-FN 333 ACHESON (known as EMRALON 333) is supplied ready for use, but it should be mixed thoroughly by stirring. For best results, use a low speed propeller-type mixer. Do not vortex or agitate violently, as air entrapment or foaming may cause separation of solids.
- Application
- BONDERITE S-FN 333 ACHESON (known as EMRALON 333) is normally applied by spray techniques. An external atomizing type gun using an MBC #30 nozzle is recommended. Optimum coating thickness is 0.001 inch (25.4 microns). USE ONLY BONDERITE L-FG SB-3 ACHESON ( known as SB-3 SOLVENT) FOR CLEAN-UP. Incompatible solvents will cause gun blockage. BONDERITE S-FN 333 ACHESON (known as EMRALON 333) can be overcoated for repair purposes without removing the entire original film. Sand lightly or use steel wool to feather the edges of the area to be repaired. Light abrasion of the surrounding areas is also recommended for maximum adhesion. Then apply BONDERITE S-FN 333 ACHESON (known as EMRALON 333) using the same spray procedures as for the initial application. Follow the standard cure cycle as stated below.
- Curing
- BONDERITE S-FN 333 ACHESON (known as EMRALON 333) may be cured by exposure to any of the time/temperature conditions indicated in the following table. It is essential that the high boiling solvents in BONDERITE S-FN 333 ACHESON (known as EMRALON 333) be removed gradually before the cure is completed or the coating will be marred by blisters. Gradual removal of the solvent can be accomplished by preheating the coating for ten minutes at 149C (300F) or 177C (350F) before curing.
- Surface Preparation
- Product Application:
Properties
- Physical Form
Packaging & Availability
- Packaging Type
Principal Information
- Group Principal Number
- S000218
- Principal
Other
- Color
- Black
- Color (SDS)
- Black
- IATA/ICAO Proper Shipping Name
- Paint
- IATA/ICAO UN Number
- UN 1263
- IMO/IMDG Proper Shipping Name
- Paint
- IMO/IMDG UN Number
- UN 1263
- Insoluble in (SDS)
- Water
- Item Number
- Odor (SDS)
- Solvent
- Temperature Control
- Yes
- USA/DOT Proper Shipping Name
- Combustible liquid, N.O.S. (methoxy propyl acetate)
- USA/DOT UN Number
- NA1993
- Application Information
Value Units Test Method / Conditions Application Temperature 204.0-232.0 °C °C continuous - Material Composition
Value Units Test Method / Conditions Solid Content 28.0 % % by weight of wet product Volatile Organic Compounds (VOC) 808.0 g/L g/L of wet product - Mechanical Properties
Value Units Test Method / Conditions Coefficient of Friction 0.09-0.1 - as static and kinetic Wear Resistance 200000.0 - Modified Hartmann tube at 180# of load - Physical Properties
Value Units Test Method / Conditions Coverage 6.54 m²/kg m²/kg at 25 μm dry film thickness, of wet product Density 1.13 - Flash Point 57.0 °C °C Storage Temperature max. 80.6 °F °F - SDS Physical and Chemical Properties
Value Units Test Method / Conditions Boiling Point (SDS) min. 35.0 °C °C Evaporation Rate (SDS) 1.0 % % Flash Point (SDS) 57.2 °C °C Pensky-Martens Closed Cup (PMCC) Lower Explosive Limit (SDS) 1.5 % % Relative Vapor Density (SDS) 1.0 - Specific Gravity (SDS) 1.12-1.14 - Upper Explosion Limit (SDS) 10.0 % % Vapor Pressure (SDS) 0.3 - at 20°C Viscosity (SDS) 150.0-1200.0 cPs cPs Volatile Organic Content (VOC) (SDS) 808.0 g/L g/L - Shelf Life & Stability
Value Units Test Method / Conditions Shelf Life 2.0 -