Enhanced TDS
Identification & Functionality
- Blend
- No
- CASE Ingredients Functions
- Chemical Family
- Country of Origin
- Function
- Binder
- Product Code
- MITM11342
- Single Ingredient
- Yes
- Technologies
- Product Families
Features & Benefits
- CASE Ingredients Features
- Labeling Claims
- Key Features
- High durability and toughness.
- Excellent adhesion over various road surfaces.
- Rapid drying.
- Excellent retention of glass beads.
- Offers low annualized cost versus epoxy and thermoplastic systems.
Applications & Uses
- Coating End Applications
- Product Applications
A wet film thickness of ~ 750 μm (~ 500 μm dry) is suggested for best durability, while thinner lines, e.g., ~500 μm wet, will offer accelerated drying. For thicker films, large particle size glass beads are suggested for optimum retroreflectance and wet night visibility. A bead drop rate of approximately 0.8 kg/lt of paint (0.6 kg/m²) for a 10cm line and ~ 750 μm film thickness is a suitable initial range which can be fine-tuned for performance. The dry-to-no- pickup time is approximately 2–5 minutes for a single line application, depending on conditions. Traffic paints based on FASTRACK™ HD-21A Emulsion offer application with airless or conventional spray equipment to asphalt, concrete, or existing road markings that are adhering well to the pavement surface. Air and surface temperature should be above 10°C, and at least 3°C above the dew point during application. Paints will require longer drying times when the relative humidity exceeds 90%.
Properties
- Physical Form
Safety & Health
- Disposal Considerations
Dispose in accordance with all, local or national regulations. Empty containers may contain hazardous residues. This material and its container must be disposed in a safe and legal manner.
Packaging & Availability
- Packaging Type
Principal Information
- Group Principal Number
- S000005
- Principal
Storage & Handling
- Handling Information
Clean-up is accomplished with clean or soapy water to remove wet paint from equipment. Stainless steel equipment should be used, and typical paint solvents can assist if removal of dried paint from tools and equipment is necessary. All solvents and solvent- borne paint should be removed from tanks and spray equipment prior to handling waterborne paints to avoid contamination, and equipment should be cleaned after each use. An ammonia solution can be floated on the surface of stored paint to prevent skinning.
- Storage Conditions
Store products in tightly closed original containers at temperatures recommended on the product label.
Other
- Appearance
- Opaque white to off - white liquid
- Appearance (SDS)
- White milky liquid
- Item Number
- Odor (SDS)
- Ammonia odor
- Other Hazards
- No data available
- USA/DOT UN Number
- Not Applicable
- Chemical Properties
Value Units Test Method / Conditions pH 10.2 - - Shelf Life & Stability
Value Units Test Method / Conditions Shelf Life 0.0 d d - Physical Properties
Value Units Test Method / Conditions Density 1.06 g/mL g/mL wet Film Forming Temperature 23.0-27.0 °C °C Viscosity max. 150.0 cPs cPs Brookfield Viscometer at 25°C, spindle #1, 30 rpm - Material Composition
Value Units Test Method / Conditions Solid Content 49.0 %(W/W) %(W/W) - SDS Physical and Chemical Properties
Value Units Test Method / Conditions Boiling Point (SDS) 100.0 °C °C Water Evaporation Rate (SDS) max. 1.0 % % Butyl Acetate = 1 Melting Point (SDS) 0.0 °C °C Water Relative Density (SDS) 1.06 - Relative Vapor Density (SDS) max. 100.0 - Air = 1, Water Vapor Pressure (SDS) 17.0 mm Hg mm Hg At 20°C Viscosity (SDS) 10.0-150.0 mPa.s mPa.s Volatile Content (SDS) 50.0-52.0 % % Water pH (SDS) 10.0-10.6 -