Enhanced TDS
Identification & Functionality
- Blend
- No
- CASE Ingredients Functions
- Chemical Family
- Function
- Binder
- Product Code
- MITM10491
- Single Ingredient
- Yes
- Technologies
- Product Families
Features & Benefits
- CASE Ingredients Features
- Performance Highlights
EBECRYL LEO® 10103 is characterized by:
- Low viscosity
- Good cure response
UV cured products based on EBECRYL LEO® 10103 are characterized by the following performance properties:
- Low residual odor
- Low extractables
The actual properties of UV cured products also depend on the selection of the other formulation components, such as oligomers, reactive diluent(s) and additives.
Applications & Uses
- Application Method
- Compatible Polymers & Resins
- Cure Method
- Ink & Toner End Applications
- Markets
- Applications
- Product Application
Formulated UV curable products containing EBECRYL LEO® 10103 may be applied by flexography, screen, gravure, direct or reverse roll. EBECRYL LEO® 10103 is recommended for use in:
- Low migration inks
- Low migration overprint varnishes
- Formulation Information
The recommended level of EBECRYL LEO® 10103 in an ink or coating is 10-20% to obtain balanced surface and through cure. For best performance, EBECRYL LEO® 10103 must be combined with a synergist to overcome oxygen inhibition. For low migration offset inks, polymeric amino benzoates can be used. For flexo inks and OPVs, EBECRYL LEO® 10103 can be combined with low migration amino acrylates such as EBECRYL® 85, EBECRYL LEO® 10551, EBECRYL LEO® 10552 and EBECRYL LEO® 10553.
Properties
Regulatory & Compliance
- Quality Standards
Packaging & Availability
Principal Information
- Group Principal Number
- S000001
- Principal
Storage & Handling
- Storage Conditions
- Care should be taken not to expose the product to high temperature conditions, direct sunlight, ignition sources, oxidizing agents, alkalis or acids. This might cause uncontrollable polymerization of the product with the generation of heat.
- Storage and handling should be in stainless steel, amber glass, amber polyethylene or baked phenolic lined containers. Procedures that remove or displace oxygen from the material should be avoided. Do not store this material under an oxygen free atmosphere.
- Dry air is recommended to displace material removed from the container. Wash thoroughly after handling. Keep container tightly closed. Use with adequate ventilation.
Other
- Appearance (SDS)
- Clear liquid
- Color (SDS)
- Clear pale yellow
- Insoluble in (SDS)
- Water
- Item Number
- Odor
- Low residual odor
- Odor (SDS)
- Ester like
- Other Hazards
- Polymerization may occur from excessive heat, contamination or exposure to direct sunlight, Contact with skin may cause a cross-allergic reaction in persons already sensitized to acrylates.
- Protect from Freezing
- Yes
- USA/DOT UN Number
- Not Applicable
- Shelf Life & Stability
Value Units Test Method / Conditions Shelf Life 0.0 d d - Physical Properties
Value Units Test Method / Conditions Density 1.1 g/cm³ g/cm³ Storage Temperature 39.2-104.0 °F °F Viscosity min. 6000.0 cPs cPs At 25°C - Material Composition
Value Units Test Method / Conditions Residual Solvent Content max. 10.0 ppm ppm - SDS Physical and Chemical Properties
Value Units Test Method / Conditions Boiling Point (SDS) min. 100.0 °C °C Density (SDS) 1.09 g/cm³ g/cm³ Flash Point (SDS) min. 100.0 °C °C Cleveland Open Cup Vapor Pressure (SDS) max. 1.33 hPa hPa at 20°C Volatile Content (SDS) max. 0.3 % %